CNC Parameters fanuc series 6 10 11 15 16 18 21

[admin]

CNC Parameters fanuc 6M
    To set parameters, set the PWE (Parameter Write Enable) switch on the main printed circuit board inside the machine to ENABLE. The machine will alarm.

Back up front, set the dial to MDI mode. Press the PARAM key.

Set TV CHECK to 0.

Set PUNCH CODE to 1.

Set INPUT DEVICE 1 to 1

Set INPUT DEVICE 2 to 1

Page down to 311. Set it's value to 11001001.

Go to 340 and 341. Set both of these to "2".

Restore the PWE switch to disable.

Reset, then power cycle the machine.


PC Settings
Baud: 4800
Code: 7 data bits / ASCII Even
Stop Bits: 1
EOB: LF
Handshaking: XON/XOFF

ADVANCED

Leader: %LF
Trailer: %
Skip lines which contain: %

IO Command Settings for PC-DNC plus Users
   

Additional Notes
    To input a program, enter EDIT mode. Press PROG, key Oxxxx then press READ.

To output a program, enter EDIT mode. Press PROG, key Oxxxx then press PUNCH.

[admin]

CNC Parameters  fanuc 10M
    To set parameters, move dial to MDI mode on machine.
Press SETTINGS key. Change PWE (#8000) to 1. The CNC will alarm.

Under Settings:

0000 to xxx01000 (ISO)
0020 to 2
0021 to 2

5001 to 1
5002 to 2
5110 to 3 (XON/XOFF)
5111 to 1 (1 stop bit)
5112 to 10 (4800 baud)

Remember to set the PWE back to 0 (disable) after changing parameters.


PC Settings
    Baud: 4800
Code: 7 data bits / ASCII Even
Stop Bits: 1
EOB: LF
Handshaking: XON/XOFF

ADVANCED

Leader: %LF
Trailer: %
Skip lines which contain: %

IO Command Settings for PC-DNC plus Users
   

Additional Notes
    To output a program, set the CNC to "edit" mode. Display the program you wish to send on the screen, then use the right arrow keys until PUNCH appears. Press PUNCH, EXECUTE.

To input a program, set the CNC to "edit" mode. Display a program on screen. Use the right arrow keys until READ appears. Press READ, EXECUTE.

[admin]

CNC Parameters fanuc 0M/0T
    To set parameters, move dial to MDI mode on machine.
Press SETTINGS key. Set ISO = 1 and I/O = 1.

Set PWE to 1 (control will alarm)

Go to PARAMATERS.

Set parameter 2's left bit to 1. The other bits should be left at their current values. ex: 1xxxxxxx

Set 552 to 10 (4800 baud)

Set 553 to 10 (4800 baud)

Return to SETTINGS, set PWE to 0.


PC Settings
    Baud: 4800
Code: ASCII Even
Data bits: 7
Stop Bits: 1
EOB: LF
Handshaking: XON/XOFF

ADVANCED:
Leader: %LF
Trailer: %
Skip lines which contain: %

IO Command Settings for PC-DNC plus Users
   

Additional Notes
    To output a program, set the dial on the machine to EDIT mode. Press PROGRAM softkey, followed by Oxxxx, then press OUTPUT START.

To input a program, set the dial on the machine to EDIT mode. Press PROGRAM softkey, followed by the INPUT key.

[admin]

CNC Parameters fanuc 16/18/21
    Place the NC in MDI mode
Press the SETTING function key until the "SETTING(HANDY)" page is displayed.
Position the cursor on "PARAMETER WRITE" field. Set to 1 by pressing the "ON:1" softkey.
(If the screen changes to an alarm message, press SETTING to return)
Cursor down to TV Check. Set to Off (0) by pressing the "OFF:0" softkey.
Cursor down to Punch Code. Set to ISO (1) by pressing the "ON:1" softkey.
Cursor down to I/O Channel. Set to 0 by pressing the "OFF:0" softkey.
Press the SYSTEM key once, then the PARAM softkey.
Find and input the following parameters. Be sure to remember that bit 7 is the leftmost bit and bit 0 is the rightmost bit on parameters where individual bits are entered.


20 = 0 (Channel 1) - this is a duplicate of the I/O Channel field on the SETTING(HANDY) screen.

100 bit 7 = 1 (NULL is ignored)
100 bit 6 = 0 (RESET can stop operation)
100 bit 5 = 1 (DNC mode fills buffer)
100 bit 3 = 1 (LF)
100 bit 2 = 0 (LF)
100 bit 1 = 0 (no TV parity checking)
101 bit 7 = 1 (no NULL feed before/after program)
101 bit 3 = 0 (EIA or ISO automitically detected/7 data bits - channel 1)
101 bit 0 = 0 (1 stop bits - channel 1)
102 = 0 (RS232 DC code control - channel 1)
103 = 11 (9600 baud rate - channel 1)
110 bit 0 = 0 (unified control of IO channels)

Other values for parameter 103 (value = baud): (1 = 50; 2 = 100; 3 = 110; 4 = 150; 5 = 200; 6 = 300; 7 = 600; 8 = 1200; 9 = 2400; 10 = 4800; 11 = 9600; 12 = 19200)

When done, press the SETTING key to return to the "SETTING(HANDY)" screen. Select the "PARAMETER WRITE" field and set to 0.
Restart your CNC control.


PC Settings
    Baud: 9600
Code: 7 data bits / ASCII Even
Stop Bits: 1
EOB: LF
Handshaking: XON/XOFF

ADVANCED:

Leader: %LF
Trailer: %
Skip lines which contain: %

IO Command Settings for PC-DNC plus Users
   

Additional Notes
    To output a program, set the CNC to "edit" mode. Press the PROG key on the control panel. Display the program you wish to send on the screen by keying in the program number then pressing the down-arrow (next line) button. Press the Operate (OPRT) softkey. Use the right arrow keys (in softkey row under LCD screen) until PUNCH appears. Press PUNCH, EXECUTE.

To input a program, set the CNC to "edit" mode. Press the PROG key on the control panel. Press the Operate (OPRT) softkey. Use the right arrow keys (in softkey row under LCD screen) until READ appears. Press READ, EXECUTE.

[admin]

CNC Parameters fanuc15M/15T
    To set parameters, move dial to MDI mode on machine.
Press SETTINGS key. Change PWE (#8000) to 1. The CNC will alarm.

Under Settings-Handy, set:

TVCHECK = 0 (OFF)
PUNCH CODE = 0 (ISO)

Under Settings-Service set:

0000 to xxx01000
0020 to 2 (device: input/foreground)
0021 to 2 (device: output/foreground)
0022 to 2 (device: input/background)
0023 to 2 (device: output/background)

5001 to 1
5002 to 2
5110 to 3 (XON/XOFF)
5111 to 1 (1 stop bit)
5112 to 11 (9600 baud)

Remember to set the PWE back to 0 (disable) after changing parameters.


PC Settings
    Baud: 9600
Code: 7 data bits / ASCII Even
Stop Bits: 1
EOB: LF
Handshaking: XON/XOFF

ADVANCED:

Leader: %LF
Trailer: %
Skip lines which contain: %

IO Command Settings for PC-DNC plus Users
   

Additional Notes
    To output a program, set the CNC to "edit" mode. Display the program you wish to send on the screen, then use the right arrow keys until PUNCH appears. Press PUNCH, EXECUTE.

To input a program, set the CNC to "edit" mode. Display a program on screen. Use the right arrow keys until READ appears. Press READ, EXECUTE.