การ ตั้งค่า RS232 fanuc cnc machine

[admin]

 http://www.machinetoolhelp.com/Applications/RS232Communications.html
Fanuc ISO Protocol communication settings: (E,7,X)
The standard protocol for Fanuc controls is 4800 or 9600 Baud, Even parity, 7 data bits and either 1 or 2 stop bits (XON/XOFF, PUNCH ON/OFF). This is standard setting that will work in most conditions. Depending on environment and cable type and distance to DNC if used.

Fanuc Control Parameter settings RS232

Fanuc-3 RS232

Fanuc-3      
Parameter   Value   Comments
0014      
0069   4800   Baud rate
TV CHECK   0   0: Off; 1: On
Punch code   0   0:ISO; 1:EIA
Fanuc 6 and 9 series RS232

Fanuc 6 and 9 series            
Baud rate   Parameter
50   00010000
100   00010001
110   00010010
150   00010011
200   00010100
300   00010101
600   00010110
1200   00010111
2400   00011000
4800   00011001
9600   00011010
Parameter   Value   Comments   
311   00011000   Baud rate 2400   
340   2       
341   2       
TV CHECK   0   0: Off; 1: On   
Punch code   0   0:ISO; 1:EIA   
Input unit   0   RS232C   
Input device 1   1       
Input device 2   1       
Fanuc 0M RS232

Fanuc 0M
On the SETTINGS screen, set the following:
TVON =0
ISO = 1
I/O = 0 (port 1), I/O = 2 (port 2)
PWE = 1
TAPEF = 0

CNC
Parameter   
Port 1
(M5)

Port 2
(M74)

0002   1xxxxxx1   no effect   
0050   no effect   1xxxxxx1   
0038   01xxxxxx   xx01xxxx   
0552   9-Baud rate: 2400   no effect   
0253   no effect   10
X means can be 0 or 1            
Fanuc-
0i-M/0i-T RS232 communication

Fanuc   0i-M/0i-T   
Parameter   Value   Comments
0000   00000010   
0020   0   
0100   00100000   
0101   10000001   
0102   0   
0103   11   Baud rate
5=150
6=300
7=600
8=1200
9=2400
10=4800
11=9600
TV CHECK   0   0: Off; 1: On
Punch code   0   0:ISO; 1:EIA
Input device   0   RS232C
Fanuc RS232-10/11/12/15

Fanuc   10/11/12/15      
Parameter   Value   Comments   
5001   1       
5002   2       
5003   3       
5110   4       
5111   2       
5112   9   Baud rate 2400   
5120   4       
5121   2       
5122   9   Baud rate 2400   
5130   4       
5131   2       
5132   Enter 5-11
in parameter
depending on
baudrate   Baud rate
5=150
6=300
7=600
8=1200
9=2400
10=4800
11=9600   
TV CHECK   0   0:Off; 1:On   
Punch code   0   0:ISO; 1:EIA   
Input device   1   RS232   
Output device   1   RS232   
Fanuc-16/18/21
(M,T,I series)
To change parameters- Press the offset settings hardkey, then press settings softkey. To turn on PWE. To get to parameters press system hard key then the parameter softkey

Fanuc   16/18/21(M,T,I series)   
Parameter   Value   Comments
0000   00000010   
0020   0   
0100   0   
0101   10000001   
0102   0   
0103   11   Baud rate
5=150
6=300
7=600
8=1200
9=2400
10=4800
11=9600
TV CHECK   0   0: Off; 1: On
Punch code   0   0:ISO; 1:EIA
Input device   0   RS232
See Fanuc
Parameter backup procedure

ATA and SRAM card setup for more information

RS232 Communications Parameters settings

RS232C, RS232-c,USB to serial, Serial communications and protocol, pcmcia, Ethernet switch, and ATA communication



Other RS232 resources that are helpful
Cadem DNC- Many templates and parameters for DNC